REM-POD-EMT (REV 2.0)

PROGRAMMABLE REM-POD-EMT (REV 2.0) INCLUDES TEMPERATURE DEVIATION DETECTION AND REM SENSITIVITY BOOST

User Instructions

Specification Difference – REM-Pod-EMT (Rev 1.0) vs REM-Pod-EMT (Rev 2.0) essentially all specifications are similar with the exception of the enhanced sensitivity detection range on the new Rev 2.0 model. The new REM-Pod-EMT Rev 2.0 defaults to a sensitivity setting that when turned on, is equal to the highest sensitivity setting of our previous REM-Pod-EMT Rev 1.0 model. The user can then make an informed decision based on environmental conditions to elevate the sensitivity four more steps which doubles the detection range of our previous Rev 1.0 model. It is important to understand that this detection sensitivity may need to be adjusted downward should you encounter external interference. Interference will be noted by a random blinking green LED. The intent of this extreme sensitivity modification is to try and amplify weaker interactive energy and to also detect energy at a greater distance.

IMPORTANT INFORMATION TO NOTE:

- Always be sure to use a fresh 9VDC alkaline battery during your investigation. When a battery needs to be changed, the REM-POD-EMT LEDs may start to fluctuate randomly. Be sure to install the 9VDC battery correctly to prevent possible damage to the circuit.

- It is recommended to remove the antenna (by unscrewing it at the base) before transportation as to not incur damage to the antenna. Should the antenna become damaged at any time, please contact support at 888-344-0111. The Antenna should be snug in place however, slight movement is normal. If the antenna becomes loose, simply tighten the antenna by screwing it into place at the base.

DIRECTIONS FOR USE:

1. Remove the brown protective paper to expose the Red Acrylic top.

2. The threaded screw antenna is located on the top of the REM-POD-EMT. This may be snug but make sure it is always completely tight. Gently extend the telescopic antenna for REM use.

3. Located on the bottom of the REM-POD-EMT you will find a slide switch that turns the REM function ON or OFF. In the REM setting, the REM with EM field around the antenna will be activated.

4. The ATDD Power button located on the bottom of the Pod allows for ± 1 to 5 degree Ambient Temperature Detection. PLEASE NOTE: To activate the Ambient Temperature Deviation Detection (ATDD) circuit, the REM circuit must also be powered ON for the ATDD circuit to function. Once activated, the ATDD will do a diagnostic check and the circuit will baseline to the environment ambient temperature condition. The temperature sensor is located on the top of the REM-POD-EMT adjacent to the telescopic antenna. An LED on top of the Pod turns Red with ascending tones for each “+” degree change and a Blue LED turns on with descending tones for a “-“ temperature change.

5. Once the REM-POD-EMT is turned ON, it goes through a quick self-test diagnostic routine. You can adjust the REM detection sensitivity level to suit your needs. The REM field and strength around the antenna is adjustable using the momentary REM RANGE button on top of the Pod. Each time the button is depressed, the detection range and sensitivity will increase by approximately 20%. When adjusting the sensitivity, the LEDs located on the top of the REM-POD-EMT will blink to acknowledge the range setting. Press the momentary switch to loop through the sensitivity range settings.

Sensitivity Level # 1 = Purple LED

Sensitivity Level # 2 = Purple & Red LEDs

Sensitivity Level # 3 = Purple, Red & Blue LEDs

Sensitivity Level # 4 = Purple, Red, Blue & Yellow LEDs

Sensitivity Level # 5 = Purple, Red, Blue, Yellow & Green LEDs

6. To test the REM-POD-EMT detection range, approach the antenna (centered) from the left and right, using your left and right hands simultaneously. The maximum detection distance for your hand is approximately ± 7” from the antenna for the new Rev 2.0 model vs. ± 3” from the antenna for the Rev 1.0 model. Note: This detection distance can vary depending on environmental conditions

7. The REM-POD-EMT has an Auto and Manual Baseline Calibration adjustment. The REM Auto Baseline occurs approximately every seven seconds. This is an important function because it will automatically adjust for any interference from metal, fluorescent lights, and other conductive surfaces. If you notice any interference from handheld communication devices like walkie talkies, adjust the sensitivity level accordingly, or refrain from using them during your investigation. Use the REM Zero button on top of the Pod to baseline the REM feature if you need to. Also, if you are using more than one Rem-Pod-EMT next to each other, be sure to separate them by at least 20”.

8. The temperature circuit also has a Manual Baseline adjustment. Make sure the REM-POD-EMT has at least ten minutes to adjust to the surrounding Ambient Temperature prior to use. If the temperature in the room rises or drops gradually and “sticks” on one degree (one tone), you can push the ATDD ZERO button located on the top of the Pod to correct for this. Or, if the sound remains on for more than ten seconds, the device will automatically mute the sound until it senses the next ± 1 degree temperature change.