What makes the
Mel-8704R-500 Model so uniquely different from all other EMF meters is
that in addition to detecting AC/DC EMF fluctuations and ambient
temperature changes, it has a special REM feature. REM stands for
Radiating Electromagnetic Field. When the circuit is activated, an independent
discreet EM field is created around a mini telescopic antenna. See
Illustration A.
llustration AThis EM field can ONLY
be influenced by materials and objects with high electron
mobility (many free electrons) in other words conductive properties.
Conductivity is determined by the types of atoms in a material. Based on conductive source, proximity & strength, the EM field can be easily
changed causing some field distortion. When this happens, there are four colorful LED lights and sound that will activate. The visual and
audible response is proportional and correlates directly to the REM
field disturbance. The stronger the influence on the REM field, the
more intense the LED's and sound response. This new feature is immune
to radio waves, AC/DC EMF and other influences that may lead to a false
positive response. For best results, place the device on a
non-conductive surface when conducting your communication sessions. The
Mel-REM can also be used as a hand held device, but careful attention
should be made to keep hand and fingers toward the bottom of the
instrument. This instrument is intended to further help promote and
advance paranormal research.
Introduction
The ATDD
is designed specifically to monitor and detect a +5 deg. / -5 deg. ambient
temperature (deviation) change that occurs within an environment. When a temperature shift does occur, the
device will react quickly and produce a unique, one octave "step"
tone for each individual degree change. Incremental
"+" changes have a higher pitch while descending "-"
temperature drops have a lower pitch. This allows a paranormal investigator to
"hear" and validate any temperature change around the device from up
to 50' away (line of sight).
This device
can also help investigators become more efficient and thorough by helping to monitor
remote unattended areas throughout a house or building during an investigation
and help direct attention to an area that may have paranormal activity. In addition, the ATDD device utilizes red LEDs
for a "+" temperature change and blue LEDs for a "-"
change.
A single
multi-purpose push button is used to "tare" the circuit and mute the
sound in any of the three configurations.
Mel-8704R-REM-ATDD
User Instructions
In addition to
the basic Mel Meter operating characteristics, it combines the Radiating
Electromagnetic (REM) function which radiates an independent Electromagnetic
(EM) field around the mini telescopic antenna and the Ambient Temperature
Deviation Detection (ATDD) circuit for hot and cold spot detection. The ATDD
will produce a one octave step tone for each degree change over a ±5 degree
range.
REM:
The Mel-8704R-REM has been designed with a
separate function which radiates an independent EM field around the top of the
unit. It is believed that spirit energy can manipulate, distort and influence
such an EM field.
To activate the REM feature, simply gently pull
out the silver telescopic antenna and press in the REM button located under the
tilt stand on the back of the Mel meter. The five LED lights on the front of
the device (Green, Yellow, Blue, Pink & Red) will also blink twice as they
go through their diagnostic routine. This verifies that the system is working
correctly. To test the EM field, move your hand around the antenna area, then
touch the top of the device. All lights will be illuminated as the EM field is
interrupted. There is also a specific tone associated with each LED. It is
important to note that there could be some interference of the EM field when
the device is within certain proximity of fluorescent lights or a high power
handheld radio frequency communication device. Also, be aware that once the REM
power has been activated, it will remain powered until you turn it OFF. Be sure
to turn it OFF when not in use to preserve your battery power. The REM feature
has an automatic “zero” or baseline function. This will activate after 5
seconds only if the amount of REM field interruption (energy) is in a steady
state or not fluctuating. If the field interruption or source is continuously
changing or undulating, the circuit will not baseline. This is important
because it will help to validate that there is a dynamic or moving energy field
interrupting the REM field around the device.
IMPORTANT: Do not attempt to open this device. It will
disturb the calibration of the REM field. Do not touch the screws that hold the
case together as they could alter specific stress points on the main circuit
boards.
ATDD:
To activate the
ATDD circuit, push the power button located behind the tilt stand. Please note, the
REM circuit must also be on for the ATDD circuit to turn on. Once
activated, the ATDD will do a quick diagnostic check and the ATDD circuit will
baseline to the environment ambient temperature conditions. There is also a baseline momentary button
located on the right side of the Mel that allows you to baseline at anytime
should there be a natural or gradual temperature change in the environment.
